Showing posts with label water. Show all posts
Showing posts with label water. Show all posts
Sunday, September 14, 2014
Automatic Water Pump Controller Wiring diagram Schematic
Simple Automatic Water Pump Controller Circuit Diagram is a series of functions to control the Automatic Water Pump Controller Circuit in a reservoir or water storage. As the water level sensor made with a metal plate mounted on the reservoir or water tank, with a sensor in the short to create the top level and a detection sensor for detecting long again made the lower level and ground lines connected to the bottom of reservoirs or reservoir.
The series of automatic water pump controller is designed with 2 inputs NOR by 4 pieces and relay that is activated by the transistor. Automatic water pump schema requires +12 VDC voltage source and can be used to control the water pump is connected to AC power . Here is the complete series of pictures.
Automatic Water Pump Controller Circuit Diagram
working principle series of automatic water pump controller above is. At the time the water level is below both sensors, the output IC1C (pin 10) will be LOW, Kemudin when the water began to touch the lower level sensor, the output IC1C (pin10) remains LOW until the water touches the sensor level above, then the output IC1C (pin 10) going HIGH and active relay through Q1 and turn on the water pump to meguras reservoir.
At the muli down and water level sensors for water untouched MKA IC1C output (pin 10) remains HIGH until the new water untouched semuasensor IC1C output (pin 10) LOW and water pump died. The series of automatic water pump controller is equipped with SW1 which serves to reverse the logic of drains (the output of IC1C) and the concept of water supplied (output dri IC1D).
When SW1 is connected to IC1D the water pump will turn on when the water does not touch all the sensors and will die when all the sensors tesentuh water. Automatic water pump controller can be used to fill or drain the water according to which mode is selected via SW1.
List Component Automatic Water Pump Controller
R1 = 15K
R2 = 15K
R3 = 10K
R4 = 1K
D1 = LED
D2 = 1N4148
Q1 = BC337
IC1 = 4001
SW = SPDT Switches
Relay RL1 = 12V
Friday, September 5, 2014
Water sensitive circuit diagram

This is a water sensitive schema diagram.I suppose this schema will give you lots of benefits .I have modified this schema up to some extent and have added to our water pump moter (230 v) I think you also can use this schema for various purposes.Here I have used common IC Bc109. When you fix the sensor Dont forget to fix it over the water level.This schema operates with 4.5V to 6v.If you want to operate your water pump 230V 0r 110V you can use a rellay for that.Then this schema will switch on or off that rellay( use 6V rellay)
Note
# Use a PCB to build this schema
# Dont supply more than 6V
#Dont forget to fix the sensor over the water level
Sunday, August 31, 2014
Simple Rain Alarm or Water Detector Circuit with SCR 106CY
Rain detector schema Diagram
Rain detector schema can be applied to the project or any other hobby, which is so simple principles.When it rains plate (sensor) will receive rain. And a dedicated work has paid to SCR1 and flow control Buzzer noise.
Electronic Part List
R1 1K 1/4 W Resistor
R2 680 Ohm 1/4 W Resistor
D1 1N4001 Silicon Diode
BZ1 12V Buzzer
S1 SPST Switch
SCR1 C106B1 SCR 106CY
SENSOR See
Notes
The sensor is a small piece of PC board etched to the pattern showen in the schematic. The traces should be very close to each other, but never touching. A large spiral pattern would also work. 2. Make sure to use a loud buzzer
Saturday, August 30, 2014
water triggered alarm system with 555 timer
You can use this schema for you water tank.then you can know before over flowing your tank.on the other hand you can use this schema as a rain detector then you can know before rain comes.so I suppose this would be a so useful schema for you
Subscribe to:
Posts (Atom)