Showing posts with label volt. Show all posts
Showing posts with label volt. Show all posts
Friday, October 24, 2014
12 Volt DC Power Suplly Adaptor
This series of images you can apply to make an adapter or power suplly with the output voltage (V DC output 12V). Power supply in the only protected by a capacitor as a safety if the power supply is connected to the load on the circuit.
So I recommend using 35V capacitor with a minimum specification. The security of power supply to power the more we can menggunakkan transistor TIP, but I have not discussed it. To the diode bridge can be compiled from the 4 then you solder the diode bridge rectifier into one or you can buy a bridge rectifier so that the comb-shaped (sideways) or the box. At least I would suggest using a diode bridge 1 Ampere, in a series of adapters, the bigger the better course of ampere diode current in the circuit. Diodes like toll roads, and current as a car passing by. The larger and the width of the existing highway, the faster the flow of runs and through the circuit.
For the circuit power supply 5 V, you can change the volt regulator on the type 7805 and 7905. This application applies equally in this series. For variations such as fuse or circuit switch on / off you can try it yourself.
Transformer 18 V + - 1 A minimum CT
Minimum of 35 V + Capacitor
Thursday, October 16, 2014
Simple 500W Inverter 12 Volt to 220 Volt Circuit Diagram
This is the Simple 500W Inverter 12 Volt to 220 Volt Circuit Diagram about the the inverter, because like working outdoors, or to backup storage to use when necessary. Most of this is circuit low power, which is not suitable for practical applications. My friends said that he would be about 500 Watt. It is a good size. Use with television receivers and light bulbs as well. When looking for circuit. I get headaches.
500W Inverter 12 Volt to 220 Volt Circuit Diagram
If you are a beginner or I can not buy expensive good quality circuits. Requires only one transistor. Or if you have free time. I want to build old circuit is alive again. This circuit will accommodate all your needs. It is a simple circuit. The same principle, I take battery voltage 12V to produce a oscillator about 100 Hz and pass to a two frequency divider circuit is only 50HZ. and drive a 10 ampere transformer with 10 x 2N3055 transistor in parallel.
By a single transistor has 2A, when I use 10 transistors or 5 pairs of drive high current output. The complexity of circuit, but the principle is not it, and it is the number of transistors on a basic, easy to buy. You may be modified 100 watt power inverter To the size of transistors and transformers as well.
Note:
If you think that This circuit is not good enough. For your work. It is hard to find equipment. You do not have it now. These circuits may be viewed below. It may be appropriate for you.Source: leksound project
Friday, September 12, 2014
6 12 Volt audio amplifier circuits
The above is an amplifier circuit using supply voltages from 6 volts DC to 12 Volt DC. Power output of the amplifier is quite low with only 1 Watt 8 ohm impedance. You can apply this to the audio signal amplifiers that require strengthening are not so large as in the pocket radio.Part List :
R1 = 100K
R2 = 39R
R3 = 100R
C1 = 100nF
C2 = 100uF
C3 = 100uF
C4 = 100uF
C5 = 470uF
C6 = 100nF
C7 = 68pF
C8 = 1nF
C9 = 47uF
IC = SFC2790C
Sunday, September 7, 2014
Stereo 9 Volt power amplifier circuit
Here I will explain about the necessary voltage and power amplifier output. The voltage should have at least approximately 9Volt 30Volt voltage and maximum voltage on the DC current. For maximum output of 2 X 2Watt with impedance 8-16 ohm. Because this amplifier circuit using ic and ic is used have the equation, so that if used different ic, then the required output voltage and also differ depending ic respectively.

Part List :
Resistor
R1 = 1M
R2 = 1M
R3 = 1K
R4 = 1K
R5 = 100K
R6 = 100K
R7 = 1R
R8 = 1R
Capacitor
C1 = 1uF
C2 = 220uF
C3 = 1uF
C4 = 100uF
C5 = 5uF
C6 = 5uF
C7 = 0.1uF
C8 = 220uF
C9 = 220uF
C10 = 0.1uF
IC
U1 = ULN2274B , ULN2277 , ULN2278B
Wednesday, September 3, 2014
Build a high volt supply Wiring diagram Schematic
A light dimmer, a 1 µf capacitor and a 12 V car ignition coil form the simple line powered HV generator. The current in the dimmer is shown in Fig. B. At times tp t2, set by the dimmer switch, the inner triac of the dimmer switches on, and a very high and very fast current pulse charges the capacitor through the primary of the induction coil.
Then at a rate of 120 times per second for a 60 Hz line, a very high voltage pulse appears at the secondary of the coil. To obtain an HV dc output, use a voltage doubler. Dl and D2 are selenium rectifiers (TV 18 Siemens or ITT) used for the supply of television sets. High value output shock protection resistors, R, are recommended when suitable.
Build a high-volt supply Circuit Diagram
Wednesday, August 27, 2014
9 20 Volt amplifier circuit
Subscribe to:
Posts (Atom)
