Showing posts with label charger. Show all posts
Showing posts with label charger. Show all posts

Sunday, October 26, 2014

Solar Charger use IC LM317


At this point is a Solar Charger Circuit to is used to charge information Acid otherwise Ni-album batteries using the solar energy power. The circuit harvests solar energy to charge a 6 volt 4.5 Ah rechargeable battery in favor of various applications. The stallion has Voltage and Current supervision and terminated voltage restrict sour facilities.

Circuit uses a 12 volt solar panel and a changeable voltage supervisor IC LM 317. The solar panel consists of solar cells each one rated on 1.2 volts. 12 volt DC is presented from the panel to charge the battery. Charging current passes through D1 to the voltage watchdog IC LM 317. By adjusting its Adjust pin, output voltage and current can subsist regulated.

Solar Charger use IC LM317 Schematic
VR is placed amid the adjust pin and ground to provide an output voltage of 9 volts to the battery. Resistor R3 confine the charging current and diode D2 prevents discharge of current from the battery. Transistor T1 and Zener diode ZD conduct yourself having the status of a stop rotten switch at what time the battery is ample. Normally T1 is rancid and battery gets charging current.

After the terminal voltage of the battery rises over 6.8 volts, Zener conducts and provides station current to T1. It followed by turns on education the output of LM 317 to prevent charging. If you want to specific voltage / current output , you can replacing ZD on the circuit above.
Read More..

Saturday, October 25, 2014

Best Automatic 12V Lead Acid Battery Charger Circuit Diagram

Build a Best Automatic 12V Lead Acid Battery Charger Circuit Diagram. This Best Automatic 12V Lead Acid Battery Charger Circuit Diagram will charge any 12V lead acid battery including flooded, gel and AGM. It is fully automatic and will charge at a rate up to about 4A until the battery voltage reaches a preset point at which it will switch to a very low current float charge. 

If the battery voltage drops again the charger will begin charging until the voltage once again reaches the cut off point. In this way it can be left connected to a battery indefinitely to maintain full charge without causing damage. An LED indicates when the battery is fully charged. Sourced By Circuitsstream

Best Automatic 12V Lead Acid Battery Charger Circuit Diagram

Best Automatic 12V Lead Acid Battery Charger Circuit Diagram

 Commponents


Part

Total Qty.

Description

Substitutions
R1, R32330 Ohm 1/4W Resistor
R21100 Ohm 1/4W Pot
R4, R5, R7, R8482 Ohm 2W Resistor
R61100 Ohm 1/4W Resistor
R911K 1/4W Resistor
C11220uF 25V Electrolytic Capacitor
D11P600 DiodeAny 50V 5A or greater rectifier diode
D211N4004 Diode1N4002, 1N4007
D315.6V Zener Diode
D41LED (Red, Green or Yellow)
Q11BT136 TRIAC
Q21BRX49 SCR
T1112V 4A TransformerSee Notes
F113A Fuse
S11SPST Switch, 120VAC 5A
MISC1Wire, Board, Heatsink For U1, Case, Binding Posts or Alligator Clips For Output, Fuse Holder

Notes 

R2 will have to be adjusted to set the proper finish charge voltage. Flooded and gel batteries are generally charged to 13.8V. If you are cycling the battery (AGM or gel) then 14.5V to 14.9V is generally recommended by battery manufacturers. To set up the charger, set the pot to midway, turn on the charger and then connect a battery to its output. Monitor the charge with a voltmeter until the battery reaches the proper end voltage and then adjust the pot until the LED glows steadily. The charger has now been set. To charge multiple battery types you can mount the pot on the front of the case and have each position marked for the appropriate voltage.

Q1 will need a heatsink. If the circuit is mounted in a case then a small fan might be necessary and can generally be powered right off the output of D1.

T1 is a transformer with a primary voltage appropriate to your location (120V, 220V, etc.) and a secondary around 12V. Using a higher voltage secondary (16V-18V) will allow you to charge 16V batteries sometimes used in racing applications.

If the circuit is powered off, the battery should be disconnected from its output otherwise the circuit will drain the battery slowly.
Read More..

Thursday, October 23, 2014

Making a Solar Energy Powered an iPhone Battery Charger

The project was termed as Mighty Minty Boost as it was developed to function as iPod/iPhone charger with solar power. Aside from being small, it has a large battery capacity of 3.7V at 2000mAh and it accepts input power from 3.7V to 7V. As shown in the images below, it can become a compact USB power supply when the solar cell is removed after charging. The Velcro is used to secure the Mighty Minty Boost inside a backpack or messenger bag after unplugging the solar cell.

For faster charging, a larger solar cell can be attached to the bag. Enough power can be generated to fully charge an iPhone in about 5.5 hours and an iPod Touch in 4 hours using a slightly larger solar cell with 6V at 250mAh. The charger will automatically switch to trickle charging when the cell reaches full charge. The charging current is limited to 100mA when charging using the mini USB port and the charging is limited to 280mA when charging using the barrel plug jack

Hacks and Mods: iPhone Charger Powered Thru Solar Energy
.
The materials needed to build the charger include a small solar cell, Lithium Polymer battery charger, minty boost kit, adhesive backed Velcro, Altoids tin, connector/wire, and small double adhesive squares as shown in the images below. An input power that ranges from 3.7V to 7V maximum can be accepted by the single cell Lithium Polymer. In bright sunlight, the solar cell maxes out at approximately 5V at 100mA. A larger solar cell with 6V at 250mA can be used for faster charging.

Hacks and Mods: iPhone Charger Powered Thru Solar Energy

The images below show the assembly of minty boost kit where a JST connector is soldered to the minty boost PCB instead of connecting the battery holder in the kit. The minty boost circuit is allowed to connect to the Lithium Polymer battery charger circuit with this tiny connector. The minty boost is tested by connecting the battery pack and the charger circuit, the Lithium Polymer battery connects to the connector marked GND on the charger board and the minty boost connects to the connector marked SYS.

Hacks and Mods: iPhone Charger Powered Thru Solar Energy

To fit the charger, a notch is cut out of the other side of the Altoids tin and used double sided adhesive to secure the charging circuit to the bottom of the Altoids as shown below. The bottom of either one of the circuit boards should not touch the bottom of the Altoids tin while reconnecting the minty boost PCB and the battery to the charging circuit.

Hacks and Mods: iPhone Charger Powered Thru Solar Energy

Connecting or adding the solar cell can be done in different ways. Shortening the connector leads and plugging the barrel plug into the barrel jack on the charging circuit is one way. The other method is using another JST connector to replace the connector and plugging it into the third connector marked 5V on the charging circuit. Since there is no bog barrel plug sticking out of the side of the tin, using the second method is cleaner.

As shown in the photos below, some 2” Velcro was used to attach the solar cell to the top of the Altoids. To help protect the battery, a layer of clear packing tape was used for wrapping. N top of the two circuit boards, the battery pack is then set down. A red LED on the charger board will light up when the Mighty Minty Boost is set out in the bright sun. The iPod/iPhone/USB powered device can be connected once it is fully charged.

Hacks and Mods: iPhone Charger Powered Thru Solar Energy
Read More..

Monday, October 20, 2014

Battery Charger Circuit using Solar Cell Circuit Diagram

This is a circuit solar charger via USB cable emergency, it is an alternative circuit that uses solar cell and LM317 to regulate and make a recharge via USB for electronic equipment that can be IPODs, cell phones, MP3, tablets, etc..  

The simplicity of the circuit can be noted that he does not have much appeal, but its enough to make a simple battery charge. The Solar Cell should be 12v current should be enough for loading, 10% of the batteries.


 Battery Charger Circuit using Solar Cell Circuit Diagram


Battery Charger Circuit using Solar Cell Circuit Diagram

Read More..

Friday, October 17, 2014

Designing A Li Ion Battery Charger with Load Sharing MCP73837


Batteries often serve as the main energy source for portable electronic devices. Although they depend on batteries, portable consumer electronic products, such as GPS devices and multi-media players, often consume energy directly from an ac-dc wall adapter or accessory power adapter (or “Auto Adapter”) when the battery is low or the device is in a stationary mode. Due to their cost effectiveness over their useful life, rechargeable batteries are often used for the power source of the portable electronic device.

Attributes such as “relatively high energy density” and “maintenance free” make Lithium-Ion (Li-Ion) batteries popular in the portable consumer electronic products. Refer to the application note, AN1088, “Selecting the Right Battery System For cost Sensitive Portable Applications While maintaining Excellent Quality” (DS01088) for characteristics of Li-Ion batteries. Some examples of how to properly design with Li-Ion batteries will be discussed in this application note. 
Read More..

Thursday, October 16, 2014

USB Battery Charger Circuit Diagram

In recent years, the use of USB or Universal Serial Bus as a reliable communications interface in plenty of electronic devices have increased due to its increased speed, size and flexibility. It fundamentally consists of terminals VBUS(+5V supply), GROUND, D+ and D-. As plenty of of the devices run on rechargeable battery, it is now the trend to design the charging circuit that makes use of the power supply from the USB port to charge the rechargeable battery. This feature will make the devices more convenient to the users as the devices will get their power from the bus and requires no outside plug or cables.


USB Bus Powered Functions
Theres fundamentally three classes of USB functions on power that can be derived from the port.

  High-Power Bus The high power bus powered functions derived all its power from the VBUS and cannt draw over 100mA until its been configured. One time configured, it can draw up to five unit loads(500mA) by requesting it in its descriptor. At full load, it must be able to work between the VBUS voltage of four.75V and five.25V.

  Low-Power Bus The low power bus powered functions derived all its power from the VBUS and must not draw over one unit load (100mA) according to the USB standard. It must even be able to work between the VBUS voltage of four.40V and five.25V.

Self-Power Self power functions can draw up to 100mA from the VBUS and the rest from its outside source. This is the most simplest to design.




USB Port Powered Battery Charger
This application circuit makes use of the MCP73853/MCP73855 linear charge management controllers for cost sensitive applications. They are specially designed for USB applications and adhere to all the USB specifications governing the USB power bus. The circuit below makes use of the MCP73855 to design a USB powered Lithium Ion/Lithium Polymer battery charger by deriving the power from the USB port.
Read More..

Sunday, October 5, 2014

L200 Battery charger circuit

L200
A actual simple array charger ambit accepting about-face polarity adumbration is apparent here.The ambit is based on IC L200 . L200 is a bristles pin capricious voltage voltage regulator IC.The charging ambit can be fed by the DC voltage from a arch rectifier or centermost broke rectifier.Here the IC L200 keeps the charging voltage constant.The charging accepted is controlled by the alongside aggregate of the resistors R2 & R3.The POT P1 can be acclimated to acclimatize the charging current.This ambit is advised to allegation a 12 V advance acerbic battery.The transistor t1,diode D3 and LED are acclimated to accomplish a array about-face indicator.In case the array is affiliated in about-face polarity ,the about-face polarity indicator red LED D5 glows.When the charging action is activity on the array charging indicator blooming LED D4 glows.
L200 Battery charger circuit

Notes.

  • The circuit can be assembled on a good quality PCB or common board.
  • The values of R2 & R3 can be obtained from the equation,

(R2//R3) =( V5-2)/(Io).

Where V5 is the charging voltage (voltage at pin 5) and Io is the charging current.

  • The POT R8 can be used for fine adjustments of charging current.
  • If battery is connected in reverse polarity the RED LED will glow.
  • When the charging is going on the GREEN LED will glow.
  • The rectified input voltage to the charger can be 18V.
Read More..

Friday, October 3, 2014

6Volt Gel Cell Charger

6Volt6Volt Gel Cell Charger Circuit Diagram

This Circuit needs a adapted 10V-DC advanced end able of bartering 2 Amps. Starts the allegation aeon at 240mA and at abounding allegation switches automatically to a float action (trickle charge) of 12mA.

The capacitors are the bowl 50V (or better) type. Switching transistor Q1 is a NPN, Si-Power Output/SW, with a TO-220 case and can be replaced with a acceptable acting like the NTE291, ECG291, etc.

Timer/Oscillator U1 is a 8-pin NE555V and can be replaced with a NTE955M or ECG955M.

Resistors R4, R5, R6, and R7 are 1% metal blur types. They may not be accessible at your bounded Radio Shack/Tandy abundance and accept to be ordered in. Try Electro-Sonic or Newark Electronics accumulation stores.

Part List
Resistors are carbon, 1/4 watt, 5% tolerance, unless otherwise indicated.

 R1 = 22 ohm, 1W C1 = 0.1µF, ceramic
R2 = 270 ohm C2 = 0.1µF, ceramic
R3 = 220 ohm D1 = 1N4001
*R4 = 715 ohm, 1% Q1 = TIP31A, B, C (or equivalent)
*R5 = 3.57K, 1% U1 = NE555V (or equivalent)
*R6 = 1.40K, 1% S1 = Toggle switch, ON-OFF
*R7 = 1.47K, 1%
Read More..

Monday, September 22, 2014

Car Battery Charger description and circuit diagram

This charger will quickly and easily charge most any lead acid battery. The charger delivers full current until the current drawn by the battery falls to 150 mA. At this time, a lower voltage is applied to finish off and keep from over charging. When the battery is fully charged, the circuit switches off and lights a LED, telling you that the cycle has finished.

Circuit diagram

Parts
R1 500 Ohm 1/4 W Resistor
R2 3K 1/4 W Resistor
R3 1K 1/4 W Resistor
R4 15 Ohm 1/4 W Resistor
R5 230 Ohm 1/4 W Resistor
R6 15K 1/4 W Resistor
R7 0.2 Ohm 10 W Resistor
C1 0.1uF 25V Ceramic Capacitor
C2 1uF 25V Electrolytic Capacitor
C31000pF 25V Ceramic Capacitor
D1 1N457 Diode
Q1 2N2905 PNP Transistor
U1 LM350 Regulator
U2 LM301A Op Amp
S1Normally Open Push Button Switch
MISC Wire, Board, Heatsink For U1, Case, Binding Posts or Alligator Clips For Output

Notes
1. The circuit was meant to be powered by a power supply, which is why there is no transformer, rectifier, or filter capacitors on the schematic. There is no reason why you cannot add these.
2. A heatsink will be needed for U1.
3. To use the circuit, hook it up to a power supply/plug it in. Then, connect the battery to be charged to the output terminals. All you have to do now is push S1 (the "Start" switch), and wait for the circuit to finish.
4. If you want to use the charger without having to provide an external power supply, use the following circuit.

C1 6800uF 25V Electrolytic Capcitor
T1 3A 15V Transformer
BR1 5A 50V Bridge Rectifier 10A 50V Bridge Rectifier
S1 5A SPST Switch
F1 4A 250V Fuse

5. The first time you use the circuit, you should check up on it every once and a while to make sure that it is working properly and the battery is not being over charged. 

Read More..

Friday, September 19, 2014

Pulse Charger for Reviving Tired Lead Acid Batteries

If you own a motorcycle, a motor home, a caravan, a lawn mover, a day cruiser or maybe a vintage car you must at some point had to write off a lead acid battery. When a battery is improperly charged or allowed to self-discharge as occurs during non-use, sulphate crystals build up on the batterys plates. The sulphate preventing the battery from being fully charged and therefore it is unable to deliver its full capacity. When trying to charge a battery in this state it only gets hot and looses water, the gravity of the electrolyte is not increasing to its normal “full charge” state. The only thing you do is killing the battery completely. If a battery has a resting voltage of at least 1.8 Volts/cell and no cells are shorted, desulphation of its plates can be done. This circuit is an add-on and part for a modification of a normal charger and it takes care of the sulphate problem. Pulse Charger for Reviving Tired Lead Acid Batteries Circuit diagram: CAUTION: Before you begin a project like this remember: mains voltage is dangerous so if you are not 100% sure of what you’re doing consult a friend who has the skills or, don’t do it at all ! The project: get hold of an old charger, big or small it’s your choice depending on the size of batteries you normally handle (bigger is better). There are some tricks to boost the performance if you need it. Start by ripping out everything except the transformer and the rectifier. Some older chargers are equipped with fin rectifiers, which have high voltage drop and must be replaced. Replace with a rugged bridge rectifier that can cope with the amperes. All wiring on secondary should be short and heavy wire. The rectifier should be bolted to the chassis to keep cool. If the charger have a high/low switch it’s a bonus, if not you can in some cases add a few turns of wire on the secondary winding. The circuit; a 14-stage ripple counter and oscillator IC 4060 produce a pulse, which is the heartbeat of the circuit. The pulse is feed to the 555 timer that deicide the length of the active output. With the switch you can select long or short pulse output. The output of the 555 timer triggers the zero-cross optoisolator triac driver MOC 3041 via a transistor. This gives the charger transformer a soft start via the triac and the snubber circuit. A small power supply is necessary for the circuit and consists of T1 a transformer 15V 0.1A secondary, a bridge rectifier, a regulator and two caps. Because this project include a charger that is (X) the outcome can differ in performance from one case to another. However this do not mean that your project doesn’t work, but the efficiency can vary. Some notes the snubbercap is a high voltage AC type (X) and the resistors on the mains side is at least 0.5W type. Use a triac that can take 400V+ and 10A+, I use BTA 25.600 but this is overkill in most cases. No PCB sorry! How it works: Well the short version. The object is to get the cell voltage high enough for the sulphate to dissolve without boiling or melting the battery. This is achieved by applying higher voltage for shorter periods and let the battery rest for a while. The pulses on short range is about 0.5s on / 3s off and the long pulse range is 1.4s on / 2s off. These times can vary depending on component tolerances. Start on long pulse and if you discover “boiling” (more than with normal charging) in the electrolyte switch to short puls. Don’t leave the process unattended, at least until you know how your specific version of this project turns out. I built ver.1 of this circuit some 10 years ago and have experimented with it but I’m sure someone can improve it further.

Good Luck! Ante
Ante135@hotmail.com

Read More..

Wednesday, September 17, 2014

USB powered battery charger circuit

rangkaian
At this time I will share about the series used in the usb to charge battery. Issued voltage 4.7 Volt to 5 Volt DC suitable for battery charge the phone, as well as other batteries. 
Read More..

Sunday, September 14, 2014

Simple Battery Charger Vehicle Wiring diagram Schematic

Unlike many boots, this battery charger continuously charges the maximum current, decreasing only near full battery voltage. In this case the full load current source, transformer / rectifier was 4.4A. It tapers to 4A 13.5V, 14.0V 3A, 2A 14.5V and 15.0V in 0A.


Simple Battery Charger Vehicle Circuit Diagram

Simple


Parts:

Resistors
R1 = 0.32R
R2 = 8.2R Capacitors
C1 = x 10,000 uF 63V
D1 = 1N4004
D2 = 1N4004
D3 = 1N4004
Q1 = MJ1504
IC REG = 7815
BR1 = 1N4004x4
B1 = 12 Volt Battery
TR 20 volts AC

R1 and R2 are as high power resistor 2W, 3W, 5W or higher. Q1 and IC requires a heatsink good. If they are mounted on the same heatsink and will decrease the schema turns Q1 gets too hot.
Read More..

Saturday, September 13, 2014

Battery Charger with Temeperature Sensor

Battery


Battery with a LM35 temperature sensor on the charger used to monitor the battery temperature is in charge. Battery temperature sensor is needed because the battery temperature will rise at the time in charge. Battery temperature sensor LM35 temperature sensor has high accuracy in monitoring the battery temperature, it is because the temperature sensor LM35 is a temperature sensor that can convert temperature changes into voltage changes linearly.

Read more
Read More..

Ni Cd Battery Charger 12 18V Wiring diagram Schematic

Build a Ni-Cd Battery Charger 12-18V Circuit Diagram. A clever charger schema that safely can charge any Ni-Cd battery. Offers charge current selection, polarization detection and protection and the ability to connect many batterys in series. 

 Ni-Cd Battery Charger 12-18V Circuit Diagram


 ni-cd battery charger 12-18v circuit diagram


Ni-Cd batteries can be recharged more than 1000 times before become useless. the charging current should be the 1/10 of the (Ah) of the battery. The batteries need 14 hours to be fully charged.. Switch S2 is the current selection as follows: 50mA, 200mA and 400mA. LED D10 is the indicator for proper battery connection and/or wrong polarity checking. LED D9 is the charging indicator. The transformer is a 220V/2x12V 0.5A. 

PARTS: 
R1,R4,R5=10K 
R2,R3=100K 
R6,R8,R10=1K 
R7=820 
R9=100 
R11=15 
R12=3,9 
R13=1,8 
C1=1000uF/40v 
C2=470pf 
D1-D4,D6=1n4001-7 
D7,D8=1n4148 
D9,D10=LED 
IC=741 
TR1=BC548 
TR2=BD137 
TR3=2N3055
Read More..

Battery Charger with Temeperature Sensor

Battery


Battery with a LM35 temperature sensor on the charger used to monitor the battery temperature is in charge. Battery temperature sensor is needed because the battery temperature will rise at the time in charge. Battery temperature sensor LM35 temperature sensor has high accuracy in monitoring the battery temperature, it is because the temperature sensor LM35 is a temperature sensor that can convert temperature changes into voltage changes linearly.


At the time of the charge a battery will experience changes in temperature, where the battery temperature will begin to rise when the battery began to fill. To avoid over heat the battery, the battery temperature sensor LM35 temperature sensor is required to terminate the battery charging current to avoid overheating.

battery
Battery charger with temperature sensor schematic

On the battery charger circuit temperature sensor with temperature sensor 35 lm above the R1 is used for setting the maximum value of the desired temperature. Therefore, when the temperature was in-charge the battery begins to rise and reach temperatures setup then this series will break the current battery charge.
Read More..

Thursday, September 11, 2014

Build a Portable Nicad Battery Charger Wiring diagram Schematic

This is a Portable Nicad Battery Charger Circuit Diagram. This schema can you build easily, The portable charger is intended primarily to give model enthusiasts the opportunity of charging their Nicad batteries from a car battery out in the open. The supply voltage for the schema is regulated by IC1. When the schema is connected to the car battery, D2 lights only if the Nicad to be charged has been connected with correct polarity. For that purpose, the + terminal of the Nicad battery is connected to the base of T1 via R8. Because even a discharged battery provides some voltage, T1 is switched on and D2 lights. 

 Portable Nicad Battery Charger Circuit Diagram


Portable

Only if the polarity is correct will the pressing of the start switch, SI, have any effect. If so, the collector voltage of T1 is virtually zero so that monostable IC2 is triggered by SI. The output, pin 3, of this CMOS timer then becomes high, T2 is switched on and relay Rel is energized. Charging of the Nicad battery, via R5 and D6, then begins and charging indicator D4 lights. During the charging, C4 is charged slowly via PI and R4. The value of these components determines the mono time of IC2 and thus the charging period of the Nicad battery. With values as shown in the diagram, that period can be set with PI to between 26 and 33 min. Notice that this time is affected by the leakage current of C4; use a good-quality capacitor here. 

The charging can be interrupted with reset switch S2. The charging current through the Nicad battery is determined by the value of R, which can be calculated: Ic is the charging current, which is here because the chosen charging period is twice the nominal value of the capacity of the Nicad battery. Resistor R must be able to dissipate a power of 1/ R W. Finally, make sure that the Nicad battery is suitable for fast charging; never charge for longer than half an hour! 
Read More..

Universal Battery Charger Circuit


Universal Battery Charger Circuit Part List:

R1 = 120R-0...5W
R2 = See Diagram
C1 = 220uF-35V
D1 = 1N4007
D2 = 3mm. LED
Q1 = BD135
J1 = DC Input Socket

This is schema diagram of a low cost universal charger for NiCD - NiMH batteries. This schema is Ideal for car use. It has ability to transform a mains adapter in to a charger . This one can be used to charge cellular phone, toys, portables, video batteries, MP3 players, ... and has selectable charge current. An LED is located in schema to indicate charging. Can be built on a general purpose PCB or a veroboard. I hope you really like it.
Read More..

Sunday, September 7, 2014

USB to phone battery charger circuit

Without any  USB to phone battery charger circuit we can charging phone battery using port on USB computer , but it will quickly damage the phone battery, and the battery will bulge. Because the voltage which was issued on usb is 5 volts , while the average-voltage phone battery 3.5 - 3.7 volts. Thats why this USB to phone battery charger circuit is required , this USB to phone battery charger circuit reduce votlage to 3.7 volt usb, but will not reduce currents and  will make a durable phone battery.
USB to phone battery charger circuit diagrams
List of components :
R1 : 1 K
R2 : 330 R
R3 : 4K7
R4 : 300 R
R5 : 27R
D1 : 4.7 volt zener /1W
C1 : 100uF/16V
Q1 : BC548
Q2 : BC558A
LED1 : Green Led
X1-1   : Vcc USB
X1-4   : Ground USB
X2-1 , X2-2 : To phone battery
See also this printed circuit board ( PCB ) of USB to phone battery charger :
USB to phone battery charger printed circuit board
Read More..

Saturday, September 6, 2014

Batteries Charger PSU Ideal for Digital Cameras

This schema was created for digital cameras. Its known the digital cameras have considerable power consumption. For example my camera Minolta E223 requires approximately 800 mA. In practice a mains power supply or high capacity NiMH accumulators (batteries) can satisfy this demand. Batteries Charger & PSU Circuit diagram: This schema consists of two parts, charger and adapter. The transformer, rectifier bridge and buffer condensator are common. Adapter is quite simply its main part is an adjustable voltage regulator LM 317 according to usual setting. Output is a suitable for camera jack plug. Voltage can be adjusted in range 2-9 V. In the charger schema a 7805 fixed voltage regulator works as current generator assured constant current during charging. This charging current can be adjusted with the 100 /1W potentiometer in range about 50-300 mA indicated by a small current measuring instrument. From one to four batteries can be charged simultaneously. The switch must be set according to number of batteries, and charging current of batteries given by manufacturer must be adjusted. This schema doesnt measure charging time and charging condition of batteries. Manufacturers give charging time, usually 14-16 h. I solved this problem with a simply, cheap mechanical mains timer. I think its accuracy is sufficient.  

Sandor Dobany from Hungary
dsandor@minimail.hu

Read More..

Sunday, August 31, 2014

12 V battery charger with PUT

A short-circuit proof battery charger will provide an average charging current of about 8A to a 12V lead-acid storage battery. The Charger circuit has an additional advantage, it will not function nor will it be damaged by improperly connecting the battery to the circuit. With 220V at the input , the circuit comences to function when the battery is properly attached.
simple
The battery provides the current to charge the timing capacitor C1 used in the PUT relaxation oscillator.When C1 charges to the peak point voltage the PUT , the PUT fires turning the SCR on , which in turn applies charging current to the battery. As the battery charges , the battery voltage increases slightly which increases the peak point voltage of the PUT. The voltage on C1 increases until the zener voltage of D1 is reached , which clamps the voltage on C1 , and thus prevents the PUT oscillator from oscillating and charging ceases. The maximum battery voltage is set by potentiometer R2 which sets the peak point firing voltage pf the PUT . In the circuit shown , the charging voltage can be set from 10 V to 14 V - the Lower limit being set by D1 and the upper limit by T1.


Part List :

Resistor
R1 = 10K
R2 = 50K trim
R3 = 47K
R4 = 1K

Capacitor
C1 = 0.1uF

Diode , SCR , PUT
B1 = MDA990-1
D1 = 1N5240 10V
SCR = 2N5164
PUT = MPU131

Transformer , Inductor
T1 = Stepdown 220V to 14V
T2 = 11Z12 1:1 
Read More..